EUROTHERM 2116I PDF

Buy Eurotherm PID Temperature Controller, 48 x 48 (1/16 DIN)mm, 2 Output Relay, 85 → V ac Supply Voltage /CC/VH/ENG/F Browse our latest. Find great deals for Eurotherm I Temperature Controller With Mounting Bracket. Shop with confidence on eBay!. The i/i are compact high performance 4 digit units for measurement Model i: 48W x 48H x D mm. Display: .. Modbus®, Eurotherm ASCII.

Author: Yozshucage Sashura
Country: Croatia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 18 June 2005
Pages: 382
PDF File Size: 1.34 Mb
ePub File Size: 16.18 Mb
ISBN: 770-3-90024-587-4
Downloads: 78010
Price: Free* [*Free Regsitration Required]
Uploader: Zugore

If, at any time, no key is pressed within 45 seconds, the display will always return to the HOME display. Return for repair Error 4: This will also reset any latched Press alarms that are no longer true. The device should be mounted in close proximity to the indicator, within easy reach of the operator and marked as the disconnecting device for the indicator.

Secure the indicator in position by holding it level and pushing both retaining clips forward. Prepare the panel cut-out to the size shown. The parameter in the N0 list applies a fixed offset over the whole display range. Read our latest case studies and Successes. Check input signal If an alarm has been disabled, it will not appear in this list.

Voltage transients on the power supply must not exceed 2. Voltage rating Cleaning The maximum continuous voltage applied between any connection and ground must not exceed Vac. Electrostatic discharge precautions When the indicator is removed from its sleeve, it is vulnerable to damage by electrostatic discharge from someone handling the indicator.

  INTERPRETACION DEL HEMOGRAMA CANINO Y FELINO PDF

Eurotherm 2116i Manuals

Pressing and again will show two decimal points in those alarms that. The information contained in these instructions is subject to change without notice. You may also apply a 2-point calibration as follows: We use cookies to provide you with a better onsite experience. Do not use water or water based products to clean labels or they will become illegible. Alarm eurptherm is active and it is a Low alarm. Return eurothrrm repair Error 2: Charged capacitors Before removing the indicator from its sleeve, switch off the supply and wait two minutes to allow capacitors to discharge.

Tactile buttons ensure positive operation. Refer to the accompanying documents Personnel Electrically conductive pollution for example carbon dust must be excluded from the cabinet in which the indicator is mounted.

Free shipping

The following safety symbols are used on the controller: To avoid this, before handling the unplugged indicator discharge yourself to ground. Alarm 2 BBB or to Press change the setpoint. All isolated inputs and outputs have reinforced insulation to protect against electric shock.

Sense of the output.

Stuck button, or a button was pressed during power up. If the alarm is disabled, or or will be shown. Eurotherm Controls Limited, Export Dept. A Eurotherm Controls Inc.

The factory default is 2. OP1 will flash when an alarm attached to the logic output becomes true.

  FONCTION HOLOMORPHE PDF

Press and release quickly the eurothfrm be flashed for 0. This is normally alarm 1. The filter requirements will depend on the type of load. The other lists are shown on the next page. It may be necessary to fit a filter across the relay output to suppress conducted emissions.

Eurotherm Temperature Controller | eBay

If the packaging or the indicator are damaged, do not install the product but contact your nearest Eurotherm Controls agent. The operator interface can be customized to present only those eruotherm that an operator needs to see and adjust. Installation must be carried out by qualified personnel. O0 to reach the Access List Heading. D5 Press twice and together.

High alarm 2 has been selected. In the event of a failure in the indicator or the sensor the following diagnostic alarm messages are provided.

i and i Compact and Economical Indicator & Alarm Unit | Eurotherm by Schneider Electric

Power Isolation The installation must include a power isolating switch or circuit breaker that disconnects all current carrying conductors. It will go steady when the alarm is acknowledged but still true. Failure to observe this precaution may damage the indicator or cause some discomfort to the user. Press and to select a parameter in the normal way.