ANILAM 1100M PDF

I have an anilam that quit working. Will the drive motors from the anilam work with a mach 3 system. And where does a person find a. Hello, Out Anilam m 2 axis system is giving us no video and the computer will not boot. Does anyone know how to repair the system?. Anilam is the company that makes the control. I run a Sharp knee mill with a Aniliam M control. I’m not familiar with the M or sure what.

Author: Samular Kem
Country: Jordan
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 18 October 2004
Pages: 495
PDF File Size: 4.77 Mb
ePub File Size: 15.98 Mb
ISBN: 195-5-45507-826-4
Downloads: 75066
Price: Free* [*Free Regsitration Required]
Uploader: Yozshujind

If it is go to the 2 axis single box servo section located later on in this chapter. Zero the display and zero the axis. The 11100m message is what you should see.

Type in the following M code M Y1. Make sure all the function keys under the screen work Remove the hold down bracket. The mill I run is good for one-off stuff. It can also convert an existing G-code program to Anilam. DNC configuration suggestions are as follows. We have seen if you tap on this power supply the distribution board will reset. Check the markings on the encoder.

We have decided to disable the message even though the software is still sending the condition that would have made them appear. Usually pin 1 is down but does not always have to be. Is the voltage still OK? Is your drive card the same as the one in the drawing?

  CRYSTAL OSCILLATOR CIRCUITS KRIEGER MATTHYS PDF

Anilam 1100M Programming Manual CNC Three Axis

Incidentally, I’m thinking of painting the mill white, because although it may turm out to be an ok thing, right now it’s like a gigantic white elephant sitting in my garage, a two-ton cast iron monument to my impulsive buying habits.

So, the control software appears to run properly on the PC. Using the up and down arrow keys select Setup Utility and press the Enter key. If you do not have this cable anilma must add a 12 gauge or 14 gauge stranded wire between cabinets.

Similar Threads Anilam t Offline software, anyone have it? After you think you found the answer to the problem do the following.

Controller & Computer Solutions > Anilam m software

If you’re not ready for CAM programming you can do most everything if you learn the machines geometry calculator. It will be much cheaper and you won’t have to rely on Anilam for support.

Normally the motor should resist you and not allow you to hand crank it. That aanilam to be the most well-proven route, and it would improve the machine’s capabilities considerably.

The X key will high-light and you press 0 and the Enter key. This is required prior.

Anilam M Programming Manual CNC Three Axis pdf – CNC Manual

Qnilam would not put a lot of money in that control. Locate the motion control board. You really do have backlash in the system and need to fix the mechanical problem. He will help you. Once you figure it out laying out 2-d stuff is a snap. You need to order part s.

  DIN 50324 PDF

If it does say test passed then reconnect the cable to the com 2 port and remove it from the Distribution board. Are you getting a Lost sync with distribution board message? You need to order a new one. It was my attempt to preclude my query being one of anilak, which people look anilamm.

Machine Controllers Software and Solutions. I did have an issue with the motherboard on one of my machines and bought a generic one off of E-Bay, I could give you more details on that if you are interested.

Slowly tighten the GIB until a. Finally the computer responded and only a soft reset occurred which causes both the computer and the distribution board to get back in sync. You must do the following first!! Locate your diagnostic disk that should be located in the programming manual. After the computer boots from the diagnostic disk, select F1 key in order to run the software.

Go to the setup utility screen.