EUROSEC CPX INSTALLATION MANUAL PDF

Wire the LCD RKP as shown in the wiring section of this manual. Replace the .. The Eurosec CP8 LCD has two log modes. These are: a). gardtec eurosec cpx installation manual · Home · Blog · About · Press · Contact · Home · Blog · About · Press · Contact. Powered by カスタマイズ可能なテンプレート . A range of alarm system user guides and manuals for owners and clients. Accenta 6 · Euro 46 User Manual · Euro Mini User Guide · Eurosec CP7/CP8 LED .

Author: Tygogar Tauzil
Country: Eritrea
Language: English (Spanish)
Genre: Software
Published (Last): 14 March 2012
Pages: 378
PDF File Size: 8.93 Mb
ePub File Size: 14.40 Mb
ISBN: 156-5-25777-932-3
Downloads: 85894
Price: Free* [*Free Regsitration Required]
Uploader: Mokree

Setting or Unsetting the system using the code that is programmed as User 7 will activate a Duress signal.

Alarm System User Guides And Manuals

This Site ID will identify what system is calling you. Please re-enable javascript to access full functionality. OR Press No display will show: G-Tag Proximity Tags may be used for setting and unsetting the system. See Advanced Code Programming section for details. All Zones ON 15 Time will count down 3 Exit the premises via the authorised exit route the exit tone will change if any detectors are violated during exit 4 Once the premises are secure listen from outside the protected area that the exit tone returns to the continuous tone.

If you wish to program other User Codes return to step 4 Or Press 0 to return to: More than 24 key presses will cause a keypad tamper. Servicing may also be a requirement of you insurance policy. Local legislation may prevent the use of Duress signals.

CPX programming guide/manual

To unset repeat this operation. I mean do some kind of connection or make any changes through the keypad?

  40 RUDIMENTI BATTERIA PDF

Zone remove is only effective for the one set. This also applies to cut cables. Several functions may not work. Your installation instaloation will have informed you as to the type of reset that your system is set for. However please use the forum for normal enquiries as this allows others to answer and learn from your question. Entering will delete an existing code Note: Remember me This installatlon not recommended for shared computers.

Follow the instructions from step 3 above. Pressing 7 will take you to back to the last event of the previous day.

User Manuals – Smith Security

Follow the instructions for programming User Codes onto your system up to the point when you would enter the User Code. To unset insert the key and turn vpx the OFF position.

At this point it is essential that you contact your installation company. In this instance using will nistallation a Duress code to your central station when you Set or Unset your system. If your system has remote communications fitted your installation company may have programmed the system so that you initialise the Access Remote call usually on lines with incoming calls barred.

Keypad Tamper The keypad will monitor the number keys that are pressed without a valid User Code being entered. Each GTag will be identified on an individual basis when it is used to Set or Unset the system.

This determines if using this user code to Set or Unset the system will trigger the Vo-Comm for more details on Vo-Comm please refer to the Vo-Comm section. In order for this to function additional hardware would be required. If your installation company has given you keyswitches for the operation of your system some user codes may have been reserved for use by these keyswitches. A fault sounder will start, enter a valid User Code to stop the fault sounder.

  HISTOLOSKI ATLAS PDF

I am using only 6 zone, should I leave the 2 zone as there are on the panel or do I need to do anything with them? If you wish to accept the name shown press Yes and jump to step 13 Code Type. The display will clear once the power is restored. The User Code levels available and the functions available for the levels are: I assume you have recieved it ok? To change this press No until the required setting On or Off is displayed then press Yes. How do I change the master default code of ?

A Master level code may change the status of the Chime between On and Off. Posted 31 December – It’s a community-based project which helps to repair anything.

Eurosec CPX User guide – Home Security Systems |

If you do not acknowledge the call or hear the rising tone the Vo-Comm will repeat the message several times and then go on to dial the remaining telephone numbers until the call is acknowledged. System Tampers The full security system is tampered, any attempt to remove covers from Keypads, Control Panel, Keypads, Bell Box es or detectors will cause a tamper alarm.

If manuzl require a blank space press YES while the ‘-‘ is displayed 14 As you press YES for the ninth character or if you have jumped from step 9 the display will change to: