DGABK datasheet, DGABK pdf, DGABK data sheet, datasheet, data sheet, pdf, Intersil, Quad SPST, CMOS Analog Switches. DGABK Datasheet, DGABK PDF, DGABK Data sheet, DGABK manual, DGABK pdf, DGABK, datenblatt, Electronics DGABK. DGABK datasheet, DGABK circuit, DGABK data sheet: MAXIM – Quad SPST CMOS Analog Switches,alldatasheet, datasheet, Datasheet search site.
|Published (Last):||11 December 2013|
|PDF File Size:||7.28 Mb|
|ePub File Size:||8.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
Maxim reserves the right to change the circuitry and specifications without notice at any time. The addition of these diodes will reduce the analog signal range to 1V below the positive supply and 1V above the negative supply.
DG211 Datasheet PDF
Parameter guaranteed by design or characterization. For the latest package outline information, go to www. For more information on TYP values rg201abk Note 3. VO is the steady state output with switch on. For information regarding Intersil Corporation and its products, see www.
In the OFF state each channel blocks voltages up to the supply rails.
Maxim guarantees that these switches will not latch up if the power supplies are disconnected with input signals still connected. These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. In either case, source-to-body diodes can be forward biased and conduct current from the signal source.
Mold flash or protrusions shall not exceed 0. Putere n-am, Tu-mi fii sprijin. Dimension M applies to lead plating and finish thickness. Pin Configurations continued To provide protection for overvoltages up to 20V above the supplies, a 1N or 1N type diode should be placed in series with the positive and negative supplies as shown in Figure 2. No circuit patent licenses are implied. When the enable input is high, a channel is selected by the address inputs, and when low, all channels are off.
No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For more information on TYP values see Note 2. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied.
This dimension allows for off-center lid, meniscus, and glass overrun. All Rights Reserved All other trademarks mentioned are the property of their respective owners. Asa cum sunt, la Tine vin! Package Information continued The package drawing s in this data sheet may not reflect the most current specifications.
DGABK (MAXIM) PDF技术资料下载 DGABK 供应信息 IC Datasheet 数据表 (3/12 页)
For this configuration dimension b3 replaces dimension b2. Device mounted with all leads soldered to PC board. Measure dimension S1 at all four corners. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Lab 6 in this note. dg201xbk
Selected parts for the query dg
SR Datasheet datasheeg Micropower Direct. Documents Flashcards Grammar checker. D, D1, and E1 dimensions do not include mold flash or protrusions.
Information furnished by Intersil is believed to be accurate and reliable. Dimension Q shall be measured from the seating plane to the base plane. The DG has a maximum turn-off time of ns and a maximum turn-on time of ns. A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use.
The DGA has a maximum sg201abk time of ns and a maximum turn-on time of ns. Feedthrough via gate capacitance may result in spikes at leading and trailing edge of output waveform. An enable input is provided. B1 maximum dimensions do not include dambar protrusions.
Copyright Intersil Americas Inc. In case of conflict between English and Metric dimensions, the inch dimensions control.
This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. E and eA are measured with the leads constrained to be perpendicular to datum -C. Dambar protrusions shall not exceed 0.
The algebraic convention whereby the most negative value is a minimum, and the dg201ahk positive value is a maximum, is used in this data sheet. Typical values are for design aid only, not guaranteed and not subject to production testing.
N is the maximum number of terminal positions. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. These are stress ratings only, datasehet functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied.
Limit diode current to maximum current ratings.